ec axial fans - hyblade ? sickled blades (s series) with full square nozzle, ? 710 highlights: C 5-blade fan, 3-phase fan motor C 10 vdc max. output / 10 ma, 20 vdc max. output / 50 ma, 0-10 v slave output, 24 v external program input, 0-10 vdc / pwm control input, 0-10 v or 4-20 ma sensor input, motor current limit C integrated pid controller, rs485 modbus rtu technology C over-temperature protected electronics / motor, alarm relay C soft start, pfc passive, line undervoltage / phase failure detection material: guard grille: steel, coated in black plastic wall ring: sheet steel, pre-galvanised and black powder paint blades: aluminum sheet insert, sprayed with pp plastic electronic enclosure: die-cast aluminum, coated in black mounting position: shaft horizontal on rotor on bottom; rotor on top on request condensate discharge holes: rotor-side direction of rotation: clockwise, seen on rotor (1) nominal data at maximum load. air performance measured as per: iso 5801, installation category a, in ebm-papst full nozzle and without protection against accidental contact. suction-side noise levels: l w a as per iso 13347, l p a measured at 1m distance to fan axis. the acoustic values given are valid under the measuring conditions mentioned and may vary accoring to the actual installation situation. with any deviation to the standard set-up, the specifc values have to be checked and reviewed once installed or ftted. for detailed information on the measuring set-up, please contact ebm-papst. curves n rpm p e w i a (460v) i a (230v) l w a in db(a) nominal data air fow nominal voltage range frequency power input (1) speed (1) current draw (1) temperature range (1) mass i ngress protection rating electrical wiring diagram ul type motor cfm vac hz watts rpm a c lbs w3g710-gs28-11f m3g150-ff 12,000 200...240 50/60 1,700 1,030 4.8 -25...60 85 ip54 a yes W3G710-GS30-01F m3g150-ff 12,000 380...480 50/60 1,700 1,030 2.3 -25...70 85 ip54 a yes pf a [ pa ] pf a [ pa ] pf a [ pa ] 0 2,000 6,000 4,000 8,000 10,000 12,000 cfm 0.2 0.3 0.4 0.8 in. wg 4,000 8,000 12,000 16,000 20,000 m3/h 2 4 0 2 0 0 1 6 0 1 2 0 8 0 4 0 9 10 11 12 7 6 8 5 3 4 1 2 13 14 15 16 0.9 0.1 0.6 0.5 0.7 1 2 3 4 5 6 7 8 9 10 11 12 a a a a a a a a a a a a 13 14 15 16 a a a a 1 2 3 4 5 6 7 8 9 10 11 12 a a a a a a a a a a a a 13 14 15 16 a a a a 1 2 3 4 5 6 7 8 9 10 11 12 a a a a a a a a a a a a 13 14 15 16 a a a a 1030 1323 1.8 3.4 74 1030 1451 1.9 3.8 73 1030 1587 2.1 4.1 74 1030 1700 2.3 4.8 78 900 867 1.1 2.2 71 900 964 1.3 2.5 70 900 1052 1.4 2.7 71 900 1123 1.5 2.9 75 750 502 0.7 1.3 67 750 558 0.7 1.4 66 750 609 0.8 1.6 67 750 650 0.9 1.7 71 600 257 0.3 0.7 62 600 286 0.4 0.7 62 600 312 0.4 0.8 62 600 333 0.4 0.9 66
w3g710-gsxx-xxf with full square nozzle cable diameter: min.4mm, max. 10 mm, tightening torque: 40.6 nm tightening torque 3.50.5 nm ?0.57 (14.5 (4x)) 31.89 (810 +1 ) 33.46 (850 -3 ) direction of air flow "v" 6.69 (170) 10.708 (2725) 0.79 (20) ?30.39 (772) dimensions shown in inches (mm)
|
